EnviroTex Lite is a pour-on plastic finish that preserves and beautifies. It cures to a thick, glossy coating in about 8 hours at 70°F, and reaches full strength and toughness in about 48 hours. This durable, resilient material requires no polishing to produce a high gloss. One coat is all that is usually required for a deep attractive finish. However, two or more coats may be applied one over the other by simply wiping the surface with alcohol and a clean cloth prior to recoating. EnviroTex Lite can be used on photos, ink, plaster, paint, wood, and table tops. One coat equals up to 50 coats of varnish. Coverage areas may vary according to the surface and method of application. It is recommended that too much be mixed for a project rather than not enough. 8 oz. Kit can cover 2 square feet. The Pint Kit can cover 4 square feet. The Quart Kit can cover 8 square feet. The Half Gallon Kit can cover 16 square feet. The Gallon Kit can cover 32 square feet.
Lite Pour-On High Gloss Finish
Rated by: Bernie S. in Paulding County, OH
This is awesome stuff! I've used it often, especially for Graduation gifts on wooden plaques, with the grads, picture, name cards, invitations, awards etc. Makes a super yet inexpensive gift. Getting this from Misterart.com is convenient, less expensive than driving 40 miles to get it at a craft store! Thank you, Misterart.com!
Rated by: amateur kichen remodler in nashville, tn
We found the trick to using this is to make sure you use enough for the self leveling to take effect. Wish there was some way to get a smooth finish on the short counter-type back splash. Likely should have put down protection on counter and flooded back splash liberally prior to coating counter top. Caution: A thicker coat will require a longer curing time. Be prepared to be without your counter tops for longer than it says in order for them to completely harden.
Rated by: Eli B in Springfield, IL
This product is hit and miss. You can follow the directions to a T every time and will only get the desired results part of the time. I think the Manufacture has poor consistency. And also, the shelf life on this stuff is very limited. Buyer beware
Rated by: Larry Jones in Terre Haute, IN
Overall, this product sucks. Following directions to the letter, success rate was less than 50%. We measured exactly, timed the mixing with a stop watch, poured as directed, and chased bubbles with a flame torch. Most would continue to bubble in the same spots till the product set. Water based stain,3 coats of Elmer's glue with drying time in between coats. Mixing in two new containers each time. New stirring stick each time. Nothing raised the success rate. I believe it has inconsistency in the manufacturing.
Rated by: matamaya12 in Danville, IN
Excellent product, easy to use! Poured EnviroTex over a broken glass mosaic, covered perfectly! MisterArt.com's pricing and timely delivery were a bonus!
Rated by: terenia in CA
This product performed exactly as described on your Web site. Delivery was prompt and the price was the best I found anywhere. Everything was packed very securely. I'm very HAPPY
Rated by: randy s in sotheast ne
i used this on a rough cedar bar top with peeled pole edges. it worked perfectly for a super deep high gloss finish with very little odor, very easy to use
Rated by: John L Feaster in Chester S.C.
I use this product and can't fine it in stores.
Rated by: STEVEN E. in chantilly, VA
This stuff is great!!!! I made a mistake and tried to use a casting resin for the top of this bar. Major mistake! I called Enviromental Tech Company and received great service and they said to use Pour On. I could not believe how easy it was to use with little to no odor. I strongly suggest a propane torch if you have an area bigger than a couple of feet. I will never look for another product for a bar top.
Rated by: natalie s. in Los Angeles, CA
I couldn't find this product sold anywhere here! I am so happy to find it online and even happier with it's results!
Rated by: tom t. in salt lake city, UT
this was very easy to use. the art works that I used it on came out great. I give it my highest rating. But it is a must to let it dry in a dust free room, or cover the item until it dries which is not hard to do.
Rated by: Marcia T. in Albany, NY
I needed a less time consuming method of applying a thick poly coating to a commercially used decoupaged bar. This was IT!! Shiny and perfect, self leveling. An inexpensive propane torch got out all the initial bubbles-- and don't forget to mask the sides of what you are covering.. I think I may have poured it on too thick because it dripped a fair amount..(though it was better not to run out of mixed product in the middle of the application process). The final product is beautiful!
Rated by: Brian N. in new york, NY
i used this for my bar top and it worked out great. the best coating that i've found.
Rated by: Maria A. in Las Vegas, NV
I have searched high and low for a clear coating to cover carved woodblocks. This product is not only the best, it is IT! Perfect covering everytime, crystal clear, easy to use, time saving over spraying individual coats of polyurethane, durable beautiful finish.
Rated by: Ann A. in Sunrise, FL
This product is terrific!! It is clear, and can be used on almost any surface. It is self leveling so it is easy to work with. I have used it to seal mosaic counter tops and to finish tile table tops. I love it!
Rated by: Greg H. in Hoffman Estates, IL
For a terrain modeler, this material is indispensable.
Rated by: karen s. in akron, OH
The product was great. I loved the results on my table.
Rated by: Caryl L. in Moore, SC
This was very easy to use. Even with shipping the price was better than I could find locally- if I could find the product at all.